New Ford Tractor

Ford 2n 8n 9n 6 Volt To 12 Volt Conversion Kit

Ford 2n 8n 9n 6 Volt To 12 Volt Conversion Kit
Ford 2n 8n 9n 6 Volt To 12 Volt Conversion Kit

Ford 2n 8n 9n 6 Volt To 12 Volt Conversion Kit    Ford 2n 8n 9n 6 Volt To 12 Volt Conversion Kit

FORD 2N 8N 9N 6 VOLT TO 12 VOLT CONVERSION KIT. This is a Brand New 6 Volt to 12 volt Alternator Conversion Kit. You can convert yourself the original Ford 6 Volt System of your tractor to 12 Volts. Ford / New Holland TRACTOR: 2N Ford / New Holland TRACTOR: 8N (1939-51) Ford / New Holland TRACTOR: 9N Notes Includes: Alternator, Resistor, Coil, Wiring Harness, Hardware Kit, 3 Brackets, Pulley, Belt V/A 12. Alternator Converson Kit, with 12-volt coil.

For models with front mount distributor. AKT0001 Alternator Kit Installation Instructions. Remove the existing generator, voltage regulator, mounting brackets and wiring necessary for this installation. Install mount with 3/8 offset facing forward, oriented horizontally toward the water pump.

Install mount with 90 degree end on the two right front head bolts. It is mounted so that the narrow side goes to the alternator, preventing the bracket from coming in contact with the fan. Next the alternator can be installed. The wide mounting foot of the alternator fits this mount. The included resistor can be used if needed with the included 12V coil. The wiring harness can now be installed (please refer to drawing). Reverse the wires on the ammeter.


Check to see if there is power at the battery terminal on the back of the alternator. This should receive constant power. There should also be constant power at the coil when the key is turned on. Start the tractor and increase engine speed until the alternator starts charging.

It may be necessary increase engine RPM to attain charge. If the alternator does not charge, re-check all steps of the installation. If manual excitation of the alternator is necessary, momentarily feed battery power to the D+ terminal at the back of the alternator using a jumper wire attached to the alternator battery stud. Our ordering system is automated. MyTractor carries a full line of tractor parts, accessories , decals , emblems and I&T Shop Service Manuals for most makes and models of tractors. We stock parts for the following brands: Allis Chalmers, John Deere, CaseIH, Kubota, David Brown, Mahindra, Deutz-Fahr, Massey Ferguson, Farmall, Minneapolis-Moline, Fendt, New Holland, Fiat, Oliver, Ford, White, International Harvester , Yanmar, J. MyTractorParts is a major North American Distributor for Aftermarket Tractor Parts including Filters, Engine part, engine kits, front end parts, tie rods, cylinders, pins, seal kits, rims, wheel hubs, axle parts, bearings, transmission gears/shafts, operator station parts, seats, PTO, hydraulic / steering / water pumps, radiators, oil coolers, hay balers parts.

Plough tools, rake teeth, alternators, starter and more!! MyTractor is an aftermarket supplier for John Deere®, Perkins®, Caterpillar®, Yanmar®, Cummins®, Kubota®, Mitsubishi®, Shibaura® and International Harvester®/Navistar®. All rights are reserved by these companies.

MyTractor is NOT an OEM supplier and does not represent these companies. All names, trademarks and part numbers are used for descriptive and identification purposes only.

The item "FORD 2N 8N 9N 6 VOLT TO 12 VOLT CONVERSION KIT" is in sale since Saturday, June 11, 2016. This item is in the category "Business & Industrial\Heavy Equipment, Parts & Attachments\Heavy Equipment Parts & Accessories\Other Heavy Equipment Parts & Accessories". The seller is "mytractorparts" and is located in USA.

This item can be shipped to United States, Canada.

  • Type: Ford Tractor Parts
  • Equipment Make: Ford
  • Model: 2N, 8N, 9N
  • MPN: AKT0001
  • Brand: ATL
  • Equipment Type: Tractor
  • UPC: 0604716708481

Ford 2n 8n 9n 6 Volt To 12 Volt Conversion Kit    Ford 2n 8n 9n 6 Volt To 12 Volt Conversion Kit